CIP Nozzles

The RML Retractable CIP Nozzles have proven to maintain cleaning performance for over 25 years and are commonly used in situations where equipment needs to be cleaned in place.

Retractable USDA CIP Nozzle L901-33

KEY FEATURES AND BENEFITS

  • Certificated as compliant with USDA Guidelines for the Sanitary Design and Fabrication of Dairy processing Equipment
  • Pneumatically opened and closed
  • 316 cast stainless steel body. Machined internally to meet hygiene standards
  • 304 machined stainless steel internal components and barrel
  • Positional feedback via externally mounted reed switches

AVAILABLE OPTIONS

  • Open and closed positional feedback
  • External visual indication flag
  • ASi control module with inbuilt solenoid, feedback connections and LED indication

Retractable Mini CIP Nozzle L901-30

KEY FEATURES AND BENEFITS

  • Small nozzle for smaller duct and tight areas to clean
  • Pneumatically opened and closed
  • 316 cast stainless steel body.
  • Fully machined to meet hygiene standards Ra 0.8
  • Tri-clover fitment

AVAILABLE OPTIONS

  • Open and closed positional feedback
  • NAMUR sensors

Retractable ASi CIP Nozzle L901-18

KEY FEATURES AND BENEFITS

  • Pneumatically opened and closed
  • Open and closed positional feedback via ASi communication protocol
  • Integrated local LED indicators: open=green, closed=amber, red=fault
  • Constructed using 304 stainless steel, fully machined externally and internally to Ra 0.8 for compliance with hygiene standards.
  • Low air consumption, up to 50% less air consumption compared with other RML nozzles
  • The ASi (Actuator Sensor Interface) allows up to 62 daisy chained nozzles to provide feedback communication on a single wire pair up to 100 metres in length.
  • An ASi signal repeater can also be added for distances greater than 100 metres.

Retractable CIP Nozzle L901-10

KEY FEATURES AND BENEFITS

  • Opened by CIP fluid pressure
  • Spring closed, close rate adjustable by external flow control valve
  • Clear polysulphane barrel
  • 316 cast stainless steel body. Machined internally to meet hygiene standards
  • 304 machined stainless steel internal components
  • Flow control valve provides adjustable drain time as dictated by system design
  • Clear barrel provides visual indication of open/close status

Retractable CIP Nozzle L901-11

KEY FEATURES AND BENEFITS

  • Pneumatically opened, spring closed
  • Clear polysulphane barrel
  • 316 cast stainless steel body. Machined internally to meet hygiene standards
  • 304 machined stainless steel internal components
  • Pneumatic open provides facility to keep nozzle open after CIP cycle, to enable forced air drying
  • Clear barrel provides visual indication of open/close status

Retractable CIP Nozzle L901-12

KEY FEATURES AND BENEFITS

  • Pneumatically opened and closed
  • 316 cast stainless steel body. Machined internally to meet hygiene standards
  • 304 machined stainless steel internal components and barrel
  • Positional feedback via externally mounted reed switches

AVAILABLE OPTIONS

  • Open and closed positional feedback
  • External visual indication flag

Retractable CIP Nozzle L901-16

KEY FEATURES AND BENEFITS

  • Pneumatically opened and closed
  • Open/closed visual indication flag
  • 316 cast stainless steel body, fully machined externally and internally to Ra 0.8 (240 grit) for compliance with hygiene standards
  • Positional feedback via externally mounted red switch

AVAILABLE OPTIONS

  • Open and closed positional feedback

Deluge Nozzle L901-34

KEY FEATURES AND BENEFITS

  • Pneumatically opened and closed
  • 316 cast stainless steel body
  • 160 degree fixed spray pattern

Fail safe design: Water pressure will open deluge nozzle even if the airlines are damaged due to fire

AVAILABLE OPTIONS

  • Open and closed positional feedback

Adaptor Flush Style M901-0101

KEY FEATURES AND BENEFITS

  • RML Nozzles are mounted to the duct or vessel by means of a welded adaptor manufactured from 304 stainless steel. One adaptor is required per nozzle installation.
  • Recommended for ducts greater than 1 meter in diameter and for flat surfaces.

Adaptor Pulled T Style M901-0108

KEY FEATURES AND BENEFITS

  • RML Nozzles are mounted to the duct or vessel by means of a welded adaptor manufactured from 304 stainless steel. One adaptor is required per nozzle installation.
  • Recommended for ducts less than 1 meter in diameter